Sail Pandora

Uncategorized

Back in CT and planning Pandora’s next move

It’s Monday morning and I am back at our “land home” in CT.  While I have only been home for a it more than 24 hours, plenty has happened in planning our “escape” to the warm weather of the Bahamas after enjoying Christmas with our family and Pandora is on the hard for a few repairs/modifications in preparation for her winter with me and Brenda.  Fortunately, there isn’t too much to do, I hope and she should be ready to go when we rejoin her in late December.

I have certainly gone on and on about what transpired on our run and why I decided to divert from our run to the BVI and take Pandora to Ft Pierce FL instead.  I’d say that a winter in the Bahamas isn’t something to be sad about and there’s always next year for a second attempt to sail to the Caribbean.

Not a bad place to visit.  This was Pandora before she was Pandora when we cruised with her prior owners in the Bahamas a few years ago.  It will be fun to be there again with her soon.  I thought that it would be fun to include a shot of our route as we made our run across the Gulf Stream and back for a stop in Beaufort NC.  From there my crew Jim and I ran Pandora down to Florida.   All and all, a satisfactory “shakedown cruise” aboard Pandora.

You can see our “loop” as we headed out and, oops, turned back.   As a point of interest, the “spots” were automatic at a predetermined interval, so you can see how our speed varied from time to time. I guess that’s all for now. Time to clean up the yard from all the leaves that fell while I was horsing around afloat.

That’s it, plans set. Sort of…

It’s Saturday night and I am sitting in the boarding area for my flight to CT.   Jim and I left Pandora in Ft Pierce today and flew home out of West Palm Beach.   I had expected that flights would be too expensive and would require us to drive the 24 hours back to CT to avoid expensive flights.  Alas, we checked with the airlines as we came within cell range off of Cape Canaveral and were thrilled to learn that we could get $141 flights home from West Palm Beach.  That as less expensive than renting car and a LOT less time consuming.

We arrived in Ft Pierce at midnight last night and anchored just inside the inlet.  After a celebratory “adult beverage” we crashed into a DEEP sleep after not getting more than a few hours of sleep per night since leaving Beaufort NC on Tuesday afternoon.  In spite of a 24 hour period of slow progress on Thursday, into the wind, we had a pretty good run and covered the nearly 500 mile run in reasonable style.

I didn’t keep track but believe that we sailed nearly half of the time and enjoyed a 100 mile 12 hour run in the first day of our trip, meaning that we sustained more than 7.5kts, a very respectable speed.   Actually, we left Beaufort with a number of other boats and passed them all, sometimes sailing at better than 9kts on a close reach.  Pretty great, actually.

However, when the wind shifted against us, we struggled to make 4.5kts against the wind for an entire day.    The problem is that Pandora is “over propped”, something that I was aware of when I purchased her in May.  This means that the propeller is too large for the engine and it can’t attain rated RPM and while this is fine in flat conditions, we aren’t able to punch into waves when the going gets rough.  I believe that by adjusting the propeller we can likely improve things but it’s unclear if this is the only problem.  I am keeping my fingers crossed that there isn’t something more sinister at work, like some sort of compression or other engine problem contributing.  More to come on that point.

Also, the refrigeration problem continues to be quite vexing and if you have been following this you know that I abandoned my BVI run due to overheating from the refrigeration.  It turns out that the compressor doesn’t work well when we are moving fast as it can’t get adequate water flow, overheats and shuts down.  You will have to review a recent post to get more info on this problem.   Again, details to come.

So, based on these issues, I decided to haul Pandora and have the prop issue sorted out and have proper thru-hulls installed on the fridge and watermaker.  You know, the type with a “scoop” on the outside to be sure that adequate pressure is available to force water into the pump and counteract the vacuum that happens when water passes over a hull opening when we are going at speed.

If you’ve been paying very careful attention to past posts, you must be wondering “what have you done with all that frozen food Bob?”   Good question, good question indeed…

As is often said, “it takes a village” and I am very fortunate to have my friend and past fellow SAGA 43 owner Carl who agreed to store my 30lbs of frozen food in his freezer until Brenda and I return to Ft Pierce after Christmas.  Of course, with Pandora out of the water, the fridge doesn’t function.  Carl says that I can pick up the food when I return in late December.  That’s of course, unless he decides that it looks “good enough to eat”.  Hmm…

As it turns out, my 1,000 run from CT to FL was much more of a “shakedown cruise” and I can say that I have been indeed “shaken down” plenty by this experience but hopefully, most of the kinks have been worked out and we can again enjoy Pandora as the beauty that she is.  It’s pretty certain that there aren’t many boats that can take the pounding that we did in the Gulf Stream with 25kts opposing the current and continue to romp along in such great style.  It was a wet but terrific ride indeed.

I haven’t mentioned yet, but on our first night out we were peripherally involved in an Air-Sea-Rescue by the US Coast Guard, in the Gulf Stream.  Fellow crew Ken wrote about this in an e-mail today that I thought I would excerpt here.

And Ken wrote…

“Some of you asked about the SAR case we observed on our way south from the Chesapeake to Virgin Gorda on Bob Osborn’s boat Pandora.

So… the story was that a sailboat in our area at about 74.5 West off Hatteras transmitted a distress signal at about 2 AM on 4 Nov and then went dark.  This is a potentially nasty piece of water with 25 to 30 Kts against the Gulfstream, which meant it was a lumpy night with rain.  The boat was at the edge of the USCG’s VHF coverage so the Coast Guard asked those of us in the area to see if we could raise a boat named “Trouble” on our radios.  “Trouble” had sent a distress call that they were taking on water.  Three of the boats in our Rally and a cargo ship turned around to search the area.  The radio traffic turned into a Abbott and Costello routine of ; “are you trouble?.. your in trouble? No your trouble,  I’m not in trouble … third base”   A USCG helicopter soon joined them.  We were over the horizon to the east but we could see the “night sun” spotlight shining down from the helicopter.  There were a lot of false sightings of flares and debris all night but finally the helo headed back via the closest logical port that a distressed boat would head for.  It was on that track line that the boat was found, with its radio off.  Apparently they turned on a hand held radio when the helicopter was hovering over the boat.  We heard the Coast Guard side of the conversation, which was very cordial.  “Is this the S/V Trouble? How many people on board? Do you need assistance? Are you no longer asking for assistance?  (This last question was repeated a few times). 

We can only speculate on what happened.  The USCG will never discourage or scold a boater from asking for assistance, although I am sure they were frustrated.  The ship that turned around undoubtedly cost its owner one hell of a lot of money, but the SOLAS convention gives them no choice.  One of the three sailboats that responded ripped his mainsail in half while maneuvering in that sloppy sea and had to abandon his transit to Virgin Gorda. 

We aborted our trip the next day when smoke filled the aft locker due to an electrical short.  The 47-foot Aerodyne was a pleasure in high winds and sloppy seas.  We only had one boarding wave swamp the cockpit.  The starboard aft locker (on the leeward side) held the propane tanks and was therefore open to the sea and filled with water, as designed.  The problem occurred when we jibed and the water filled locker slopped over and through a hole for a wire that was not sufficiently watertight.  Just that little bit of water ruined our day.  We were never in danger but Bob made the right call on the side of caution.  There was no reason to risk a fire that far from land so he turned off the refrigeration.  This meant some food would have gone bad and no one wanted to eat peanut butter and jelly for a few days at the end of the trip.

We were all disappointed that we could not continue but it turned out that a Low that was north of Haiti turned into a full blown tropical storm so we may have avoided a few more sloppy days before making landfall.

As an aside, it was warm enough in the Gulfstream for me to take a shower on deck by just standing in the rain while avoiding the salt spray over the bow. “

It was an interesting night at sea and while I hated to divert and scrub my run to the BVI for this season, I am confident that I did the right thing.  Of course, with hindsight, it seems that the main reason we had to abort, a refrigeration problem, could have been avoided if I had better understood the limitations of the refrigeration installation and had a minor modification done prior to leaving CT.  Of course, with Pandora on the hard AGAIN, this problem should soon be history, I hope.

So, back to our arrival in Ft Pierce in today’s wee hours, Jim and I were happy to drop the hook and get a good night sleep.   When I dragged myself out of a deep sleep at 07:30 today I was greeted by a lovely breeze, palm trees and balmy temperatures. 11-14-15aWhat a lovely warm dawn it was and it’s good to know that Pandora had a successful if  somewhat more “interesting” run south to her winter home.

So there you have it.  My plans for the winter?  Well, at least for now.

Hopefully Pandora won’t “shake me down” any more for a while.  But wait, she’s a boat and that’s what boats do.

I’d better run to catch my flight though…

 

If I’d only known…

It’s mid morning and we are 75 miles off of the GA coast and about 2/3 of the way toward Ft Pierce, our destination, where I will leave Pandora until Brenda and I return after Christmas to prepare for our run to the Bahamas.

We are motor sailing close hauled and making fairly slow progress which is a bit frustrating. However, our overall run has been pretty good as we sailed at quite a clip for the first 24 hours at the rate of about 200 miles a day. We expect that the winds will again be favorable once we cross into Florida early tomorrow morning and hope to sail the last 100 miles with a good NW wind behind us.

As both Jim and I have already purchased return flights from the BVI, neither one of us is too keen on paying for yet another airline ticket. With that in mind, I’ll be renting a car and we will drive straight through to Jim’s home in Wiliamsburg VA, beginning on Sunday. It’s not ideal but at least it won’t be too expensive. Such are the complexities of moving boats around.

There’s not much to report except that nothing more has broken and I feel like I understand Pandora a lot better.

One thing that I understand now is the refrigeration and if I knew then what I knew then, I would not have aborted my run and would be in the BVI by now. What I learned is that the fridge doesn’t cool well when we are in rough conditions or going fast, as the cooling pump draws in too much aerated water to properly provide cooling for the compressor. This problem could likely be eliminated by putting a new thru-hull in with a forward facing scoop, much like what is used on an engine water intake. In addition, it is commonly known that when water passes over a flush hole in the hull a vacuum is created, known as the venturi effect. As Pandora is such a fast boat, this effect causes the water pump to work much harder, against that vacuum, causing the compressor to overheat. The watermaker suffers a similar problem so I’ll have to replace that thru-hull as well. The Spectra watermaker instructions specifically warn of this problem as a cause of premature pump failure, something that I have already “enjoyed” on Pandora. For now, the simple solution is for me to just turn off the refrigeration and only cycle it as needed and not to allow it to draw down the temperature quite as low, thereby reducing the run time on the unit and minimizing overheating. It’s really unfortunate that I wasn’t aware of this sooner as great deal of frustration and expense could have been avoided.

Oh well, at least I know now.

We haven’t been in close contact with many boats for the last day or so but have talked to a few that have showed up on AIS. In particular, I was amused by a 70′ sport fisherman called “18 reeler”. The captain had a thick southern accent and I couldn’t help wondering if he made his money in the trucking business. Oh yeah, we have also had plenty of dolphins keeping us company, which is always fun.

I guess that’s about all for now as we make our way south. Oh yeah, we are officially into warm water so it’s shorts and light shirts, even at night.

BVI or bust? Busted…

If you have been watching my track on “were in the world is Pandora” you are likely scratching your head as to exactly why Pandora is underway and moving south along the US coast. So, here’s what’s going on.

Taking care of all of the “details” following our romp in the Gulf Stream at the beginning of the Salty Dawg Rally took a full five days on the Morehead City docks.  I won’t reiterate all of the issues, most of which I detailed in previous posts, but the list included plenty of items with the final task to replace the missing set-screws in the jib roller furler that were missing.

The absence of these fasteners meant that one of the upper extrusions was shifting and wore away the bolt rope and damaged part of the jib. I didn’t realize that this was a problem until we attempted to re-hoist the repaired jib. The repair required two metric set screws and finding the right size turned out to be fairly difficult and involved a cab ride to a local hardware store, a sort of nautical scavenger hunt ending with success in finding what ended up being two $30 set screws that should have cost about $1 each.

Anyway, when we had finally ticked off most of the items and I had time to begin thinking about what I was going to do next. Of course, the major issue was crew as the three had signed on for two weeks and that meant that heading out again for the BVI was not going to work as we’d never get there within the two week window.

My first thought was just to leave the boat in Beaufort, head home and then return after Thanksgiving and run to the BVI then. Yes, that seemed like a good idea. However, the rub was that getting crew to sign on for two weeks during the holidays seemed to me like a very tall order so back to the drawing board.

Ok, I’ll just continue on to Ft Pierce FL, leave the boat there and head back there after Christmas and spend the winter in the Bahamas. That seemed to be a reasonable idea even though I was very disappointed to give up the BVI after so much planning and anticipation.

After saying that we’d be leaving the boat in Beaufort, Ken and Cathy made other plans which meant that I lost them for the run to FL. Fortunately, Jim agreed to stay on and help me with the rest of the delivery. So, as I write this the two of us are working our way down the coast and should be in Ft Pierce FL late Friday or Saturday.

We left Beaufort yesterday afternoon and had a rough sail overnight with winds gusting near 30kts on a close reach. As there had been very strong winds from the south for the previous few days, the seas were pretty rough and confused as the winds clocked from the south to the west and finally NW, but we made good progress passing all boats that we encountered along the way and covering 100 miles in 12 hours, a pretty impressive run.

I expect that the remainder of the run will involve a lot of motoring but at least the boat will be where it needs to be and all settled in. So, after Christmas Brenda and I will either fly or drive south and rejoin Pandora in late December.

All and all, this run has been much more of a shakedown cruise than I had envisioned with all sorts of little surprises along the way. Hopefully, now that I know the boat better, this winter will be more relaxing and less of the “boat repair in exotic places” that it has been.

So, with the BVI totally “busted” I am hopeful that Brenda and I will have a fun winter in the Bahamas. It should surely beat the sub-zero temperatures of New England.

For now, continuing to head south to Florida and then on to home. Yes, home, I am getting a bit home sick, and can’t wait to see Brenda again, that’s for sure.

Getting to know her, getting to know all about her…

Ok, now I get it.  The last few weeks preparing for the Salty Dawg Rally and finding my way, sometimes painfully, to Morehead City NC has really been a shake-down cruise, an opportunity to get to know Pandora on an intimate level and better understand her and her systems.

On “old Pandora”, I had installed much of her equipment myself so I knew what to look for and exactly how to deal with most situations.  With Pandora “new”, It’s more like a scavenger hunt, where every little experience is a mystery and sometimes I really have no clue even if I think I know what I am dealing with.  “exactly where is that electrical smell coming from?”, “did the fridge compressor cut out because it is overheating or did it reach it’s set point and exactly what temperature is that anyway?”.

An Aerodyne 47 is a very complicated boat, well at least compared to other boats that I have owned, and sometimes I don’t even know if something is broken or not.  I just have NO IDEA what I am looking for.   Do I furl up the sail cover or leave it in place when I reef.  Furl it.  Now I know, furl it.  That was a painful lesson as I spent much of yesterday making minor repairs from when I reefed and didn’t furl.  It’s a big cover but between me and Cathy, we were able to maneuver it around in the cabin and get everything in order.   11-8-15b 010It’s all about attention to detail.  Pretty good work for an amateur, I think.11-8-15b 012Getting the sailcover off of the boom and back on was “magic” as Jim, Ken and Cathy handled the whole process.  I did the sewing.

How about getting to know her jib?  I patched the vinyl window and an area on the luff that had chafed on a rough part of the roller track where a rivet had broken, who knows how long ago.  Not serious but I’ll have it properly repaired next summer when she’s laid up for a few months. 11-18-15b 014I also received the watermaker pump head yesterday (Just how much does Saturday delivery have to cost?  Really?) and installed it.  I was getting concerned that I couldn’t back-flush the unit as required without a properly functioning pump.  All better now.

It felt pretty good to have “most” of the details worked out, both things that broke and those that just needed attending to that I didn’t even know about.  All and all, the chores took about three full days, or was it four?  And that included a lot of help from crew.   Happily, they have been very good natured about the “change of plans”.   Perhaps it was the “Pandora made” biscuits.  No, it was probably the rum. Having cold beer on hand helped too.  Did I mention that the fridge is working again?  Actually, it always worked.  That was a hard lesson.

Glad to have all of that behind me.  Well, until things get “interesting” again.  And speaking of that, I am now looking for crew and expect to try to make my run to the BVI again a few days after Thanksgiving now that I know Pandora just a bit better.

Chores or not, I did make time yesterday to watch what is billed as “the largest Veteran’s Day Parade in all of North Carolina”.   Not sure how that compares to other “largest Veteran’s Day Parades”, but it boasted a LOT of very enthusiastic participants, throwing candy at spectators, and went on and on.  The procession took nearly two hours to pass.  With a number of big military bases nearby, there was some really impressive hardware.

This one would be right at home in the desert.OLYMPUS DIGITAL CAMERAHow many helicopters do you see in your local parade?OLYMPUS DIGITAL CAMERAAnd, who doesn’t love the old Jeeps?OLYMPUS DIGITAL CAMERAI was trying to get my head around these little trucks and wondered how many beers it took when someone said, “hey guys, let’s build little trucks and drive them in public a few times a year and no, I don’t mean those embarrassing golf carts that look like a Corvette.   I am talking totally ridiculous.  Can I Have another Bud?”  “Here you go, Elmer. I want a mini truck too!”OLYMPUS DIGITAL CAMERA“No wait, I have an even better idea…  How about a motorized land boat?  And let’s make ten of them that match and drive them in circles as we move down the street.”OLYMPUS DIGITAL CAMERA“It will be awesome.  I’ll make a shrimp boat with wheels.”OLYMPUS DIGITAL CAMERA“I can make my golf cart into a Jet fighter.  It will look just like the one I flew in Nam.”OLYMPUS DIGITAL CAMERA“And we’ll have my buddy Jake bring his hot air balloon basket so he can blast flames into the air.”OLYMPUS DIGITAL CAMERA“I once saw the Blue Angles perform.  I’ll modify The Wife’s old Harley.  I am sure she’ll love it.”OLYMPUS DIGITAL CAMERA“Guys, what about me?  I want one too and I have always said that if I was going to drive a car that was REALLY tiny, it would be yellow.  Yes, bright yellow with red pin-striping. and real green running boards.”OLYMPUS DIGITAL CAMERASo, there you have it, from the sublime to the ridiculous and you will just have to decide which is the sublime and which is, well not so…

For better or worse, I now know more about Pandora than I did before I left CT.  And, as my dad used to say, “that’s more about penguins than you probably ever wanted to know”, and this is only the beginning.

How about another shakedown cruise in December?  Then I’ll really know her, all about her.  Well, except the things that I’ll learn later.

Scroll to Top